Adaptec 2110S - SCSI RAID Controller Guía de instalación Pagina 27
- Pagina / 106
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-4
Adaptec RAID Installation Guide
SCSI Termination
The basics of termination are as follows:
■ Enable termination on the devices on each physical end of a
SCSI cable. Depending upon how you configure your system,
you would either
■ Enable termination on two SCSI peripheral devices, or
■ Enable termination on the SCSI controller and one
peripheral SCSI device.
■ If you are using multiple SCSI channels on a single controller,
terminate each channel separately.
SCSI termination for Adaptec SCSI RAID controllers is configured
through the SMOR utility or from the Configure Host Bus Adapter
window in Storage Manager. The controller has four possible
termination settings, as shown in the following table:
Devices on the second bus (Bus 1) and higher (if the RAID controller
has more than two) must have Wide termination.
By using a 68-pin to 50-pin SCSI cable adapter, a Narrow device can
be attached to a Wide cable along with Wide devices. However, the
device at the end of the cable must be a Wide device so that all SCSI
signals are terminated. For internal and external cables where one
cable is Narrow, set the controller termination to High Only.
Setting Function
Auto Default—Used for all cabling conditions, except where
two Narrow cables are attached or both Narrow and Wide
cables are attached. For these exceptions, use High Only.
1
1
This termination option is not available on the 2000S or 2005S. These ZCR controllers
have only On (enabled) and Off (disabled) available, with On being the default.
High Only Terminates only the additional signals that are used on
Wide SCSI devices. This allows attachment of a Narrow
cable, or both a Wide and Narrow cable together, to be
attached to the controller.
1
Disabled Disables controller termination unconditionally.
Enabled Enables controller termination unconditionally.
COMBINED RAID IG.BOOK Page 4 Tuesday, September 25, 2001 5:46 PM
- Adaptec RAID 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec, Inc 3
- Canadian Compliance Statement 4
- Contents 5
- 3 Installing the Driver 6
- A Card and Module Diagrams 8
- B Controller LEDs 8
- C Troubleshooting 8
- E Specifications 8
- System Requirements 10
- Kit Contents 11
- About the Documentation 14
- Introduction 15
- Files and Folders 16
- Product Documentation on CD 16
- Errata and Release Notes 17
- Cache Memory Module 19
- Safety Information 22
- Installing Your Controller 24
- Configuring SCSI Devices 25
- LVD and SE Devices 26
- SCSI Cables 26
- SCSI Device IDs 26
- SCSI Termination 27
- Seating the Module 30
- Adaptec 3200S/3400S Only 30
- Installing the Controller 32
- Using SMOR 34
- Installing the Driver 36
- Windows 2000 37
- Windows NT 4.0 41
- Controller 42
- 5 Select Adaptec I 46
- 8 Start up the system 46
- Creating the Driver Disk 47
- C drive 48
- (OEM SR2 – Version 95B) 50
- Novell NetWare 54
- NetWare 4.11 Server 55
- NetWare 4.2 Server 57
- C drive named nwupdate 58
- NetWare 5 Server 60
- SCO UNIX 62
- Installing Storage 69
- Management Software 69
- Installation Prerequisites 71
- NetWare 4.11 and 4.2 72
- NetWare 5.x 74
- Red Hat Linux and FreeBSD 75
- Installing Storage Manager 76
- SCO UnixWare 7 78
- ■ K Desktop Environment (KDE) 79
- Card and Module Diagrams 80
- Adaptec ATA RAID 2400A 81
- Adaptec SCSI RAID 2000S 82
- Adaptec SCSI RAID 2005S 83
- Adaptec SCSI RAID 2100S 84
- Adaptec SCSI RAID 2110S 85
- Adaptec SCSI RAID 3200S 86
- Adaptec SCSI RAID 3400S 87
- Adaptec SCSI RAID 3210S/3410S 88
- Controller LEDs 92
- LED During Power-up 93
- LEDs During Controller Idle 93
- LEDs During Controller Active 93
- Cache Status LEDs 94
- SCSI Bus Status LEDs 95
- Troubleshooting 97
- Controller Reset Procedures 101
- NVRAM Reset 102
- Flash Mode 0 102
- Specifications 104
- RINTED IN SINGAPORE 106
Relacionado con productos y manuales para Placas base Adaptec 2110S - SCSI RAID Controller
Placas base Adaptec 3940AUW Manual de usuario
(128 paginas)
(128 paginas)
Placas base Adaptec 1045 Guía de usuario
(69 paginas)
(69 paginas)
Placas base Adaptec AHA-2742 Guía de usuario
(118 paginas)
(118 paginas)
Placas base Adaptec AHA-1744 Guía de instalación
(191 paginas)
(191 paginas)
Placas base Adaptec AVA-2825 Guía de usuario
(110 paginas)
(110 paginas)
Placas base Adaptec AHA-1540CP Guía de instalación
(14 paginas)
(14 paginas)
Placas base Adaptec AHA-1540B Guía de instalación
(14 paginas)
(14 paginas)
Placas base Adaptec AHA-2742 Guía de instalación
(25 paginas)
(25 paginas)
Placas base Adaptec AHA-3940 Guía de usuario
(102 paginas)
(102 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales