Adaptec GDT RN Series Manual de usuario Pagina 130
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
130
The „ERROR“ state of an Array Drive is very critical. There are several procedures in the ICP
Controller’s firmware to handle such cases an bring back the Array Drive in operation with-
out loosing data. The most suitable procedure for the specific case, should be elaborated
with your system administrator or our technical support. (Note: ICP vortex offers 2-day
RAID Workshops in our training center, which also focus on the resolution of such prob-
lems.
J.4.3 Menu Advanced Setup: Configure Controller
J.4.3.1 Menu Advanced Setup: Configure Controller, Controller Settings
Within the Controller Settings all relevant
parameters and settings concerning the
ICP Controller itself can be changed. All
information concerning Physical, Logical,
Array and Host Drives are stored twice
(primary and secondary configuration data) on
each hard disk. I.e., the ICP Controller
itself carries no configuration data of a
specific disk array. Out of this reason, the
migration of Host Drives between ICP
Controllers is very easy and secure, even
if the SCSI IDs and channels are changed.
Simply connect the hard disks to the new
ICP Controller, and the Host Drives will
automatically available again.
The various parameters and settings have
the following meaning:
Parameter Alternatives Description
Cache On
Off
ICP Controller cache (write and read cache) On
ICP Controller cache (write and read cache) Off
Delayed Write On
Off
Write cache On
Write cache Off
BIOS Enabled
Disabled
Removed
BIOS enabled
BIOS disabled, but <CTRL><G> allowed
BIOS and <CTRL><G> disabled
BIOS Warning Level All Messages
Fatal Errors
All ICP BIOS warnings and errors are displayed
Only fatal messages are displayed
SETUP from Flash-
RAM
Disabled
Enabled
<CTRL><G> not possible
<CTRL><G> allowed
- User's Manual 1
- Contents - Overview 3
- Limited Warranty 4
- Important Note 6
- Many Thanks to all my Friends 6
- FCC Compliance 7
- FCC ComplianceFCC Compliance 7
- FCC Compliance Statement 7
- Statement Statement 7
- Statement 7
- Table of Contents 8
- Chapter A 15
- A. Introduction 16
- A.2 Copyrights, Patents 19
- A.4 General Information 21
- A.5 Product Description 22
- Graphical User Interface 24
- DBPM Terminator 26
- GDT6538RS Overall View 31
- Chapter B 35
- B. Hardware Installation 36
- B.4 SCSI - Basics 37
- B.4.1 SCSI Cables 38
- B.4.2 SCSI Termination 43
- B.4.3 SCSI ID 43
- B.4.4 ICP SCSI Accessories 44
- B.4.5 Examples 46
- B.6.1 Trouble Shooting 51
- Chapter C 53
- C. Quick-Setup 54
- Chapter D 71
- D. Using Microsoft MS-DOS 72
- D.4 Expanded Memory Managers 73
- D.6.1 Using ASW ASPIDISK.SYS 77
- D.6.2 Using corelSCSI 77
- D.7 Installing Windows 95 78
- D.8 Installing Windows 98 80
- Chapter E 81
- E. Using Novell NetWare 82
- E.5 Tips and Tricks 85
- E.6 Notes on ARCserve 87
- Chapter F 89
- F.2 Windows NT 90
- F.2.2 The Installation 92
- F.3 Windows 2000 94
- F.3.2 The Installation 95
- Chapter G 97
- G. Using LINUX 98
- G.6 gdth driver parameters 100
- G.7 Notes 101
- Chapter H 103
- H. Using SCO UNIX V/386 104
- H.5 Further Information 109
- Chapter I 111
- I. Using UnixWare 112
- I.6 Further Information 114
- Chapter J 115
- J. The Program ICPCON 116
- J.2 The ICPCON Program 118
- J.2.1 Select Interface 119
- J.2.2 Select Controller 120
- J.3 The Menu Monitor 121
- Temperature 138
- Chapter K 147
- K. ICP RAID Navigator 148
- K.2.1 The Toolbar 149
- K.2.2 The Status Bar 149
- K.3 Select Controller 152
- K.4.1 Controllers 153
- Save Information 154
- K.4.2 I/O Processors 155
- K.4.3 Direct Access Devices 156
- The SCSI Parameters 157
- Synchronous Transfer 158
- Disconnect 158
- Tagged Queues 158
- Format a Physical Disk 159
- Deinitialize a Physical Disk 159
- Host Drives 161
- Array Drives 162
- Logical Drives 163
- Physical Drives 163
- K.5.5 Remove a Host Drive 167
- K.5.7 Parity Verify 168
- K.5.8 Parity Recalculate 168
- K.5.9 Progress Information 169
- K.5.10 Expansion of an Array 169
- K.5.11 Add a Hot Fix Drive 170
- K.5.13 Hot Fix Pool Access 171
- The ready state 172
- The idle state 173
- The build / rebuild state 173
- The fail state 173
- The error state 174
- K.6 The Statistics Window 175
- K.8 ICP RAID Navigator Help 177
- K.9 ICP Service and ICP Mail 178
- Chapter L 183
- L. Appendix 184
- L.3 Index 185
Relacionado con productos y manuales para Software Adaptec GDT RN Series
Software Adaptec GDTSETUP Manual de usuario
(218 paginas)
(218 paginas)
Software Adaptec GDTSETUP Manual de usuario
(64 paginas)
(64 paginas)
Software Adaptec AVA-2825 Guía de instalación
(35 paginas)
(35 paginas)
Software Adaptec RAID 2810SA Guía de instalación
(9 paginas)
(9 paginas)
Software Adaptec 2042900ENFR - VideOh! DVD Media Center USB 2.0 Edition Manual de instrucciones
(38 paginas)
(38 paginas)
Software Adaptec AHA-1520A Manual de servicio
(434 paginas)
(434 paginas)
Software Adaptec ULTRA160 Guía de usuario
(78 paginas)
(78 paginas)
Software Adaptec ICP5045BL Manual de usuario
(7 paginas)
(7 paginas)
Software Adaptec ASR-2045 Guía de usuario
(9 paginas)
(9 paginas)
Software Adaptec AAR-2020SA Manual de usuario
(9 paginas)
(9 paginas)
Software Adaptec ASR-5445 Manual de usuario
(5 paginas)
(5 paginas)
Software Adaptec ICP9085LI Manual de usuario
(2 paginas)
(2 paginas)
Software Adaptec AVC-2310 Guía de usuario
(14 paginas)
(14 paginas)
Software Adaptec ASR-2045 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales