Adaptec Snap Server 700i Series Guía de usuario Pagina 127
- Pagina / 238
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using Status and Drive Light Behavior to Monitor
Components
This section describes how to use the LEDs on your Snap Server 700i Series and any
SANbloc S50 expansion array to check the status of your IP SAN hardware
components.
Snap Server 700i Series
The server has two status lights; two network lights on the front of the server (for
ETH0 and ETH1); one or two network lights on the Network Interface Card on the
rear of the server (for ETH2 and ETH3, if applicable); two lights for each of the four
disk drives; and an identification light, as shown in the following illustration:
Adaptec recommends that you become familiar with the operation of these lights.
Power, System, and LAN LEDs
These status lights are located to the right of the power button. Looking at the
server from the front, the lights appear in this order, from left to right: power LED,
system LED, LAN 1 (ETH0) LED, and LAN 2 (ETH1) LED. The Disk Drive LEDs are
below the status lights, and the identification (Unit ID) LED is to the right of the
LCD display.
System LED
Power LED
LAN LEDs
Unit ID (UID) LED
Disk Drive LEDs
- Snap Server 1
- 700i Series 1
- User’s Guide 1
- Contents 7
- About this Guide 13
- Service and Technical Support 15
- Notes and Cautions 16
- Finding More Information 16
- US/Support 17
- Source and Location Content 17
- Planning Your IP SAN 19
- Windows Support 23
- Sample IP SAN Configurations 24
- Basic Configuration #1 25
- Basic Configuration #2 26
- Configuration with Mirroring 27
- GbE SwitchGbE Switch 29
- Net A Net B 29
- Net C Net C Net C 29
- GbE Switch 29
- System Requirements 31
- Installing Adaptec Storage 33
- Click Install 35
- Installing on Linux 36
- 4 Unmount the CD: 38
- Appliance and IP SAN 39
- Before You Begin 40
- Creating RAID Pools 44
- Beginning to Use Your IP SAN 53
- Setting Up VSS/VDS Access 54
- Next Steps 56
- Getting to Know Adaptec 57
- Storage Manager 57
- Navigating the Main Window 58
- The Physical Devices View 61
- The Logical Devices View 62
- The Volumes View 63
- The Snapshots View 63
- Revealing More Information 64
- Protecting Your Data 67
- Deleting a Hot Spare 69
- Mounting a Snapshot Set 72
- Creating Volume Snapshots 75
- Scheduling a Snapshot Job 76
- Creating a Mirrored Volume 80
- Extending a Mirrored Volume 81
- Changing Mirror Priorities 81
- Breaking a Mirrored Volume 83
- Deleting a Mirrored Volume 84
- Specifying Replica Site 84
- Creating Replicas 85
- Updating Replica Set 85
- Aborting a Replica Set Update 86
- Switching Roles 86
- Mounting a Replica Set 86
- Unmounting a Replica Set 86
- Breaking a Replica Set 86
- Scheduling Replica Update 87
- Chapter 7 89
- Opening the Security Manager 94
- Modifying Your iSCSI Storage 97
- Adding an iSCSI Storage Host 98
- Capacity Limitations 99
- Creating and Modifying Pools 100
- Adding Capacity to a Pool 102
- Changing a Pool’s RAID Level 102
- Deleting an Individual Pool 107
- Deleting All Pools 107
- Creating a New Volume 108
- Adding Capacity to a Volume 109
- Deleting a Volume 110
- Creating a New Logical Device 110
- Modifying a Logical Device 111
- Deleting a Logical Device 111
- Appliance 113
- Applying a New Image 117
- Checking the Current Image 118
- Monitoring Jobs in Progress 121
- Opening the Job Manager 122
- Cancelling a Job in Progress 122
- Resuming a Cancelled Job 123
- Undoing a Failed Job 123
- Viewing Status and Activity 124
- Viewing Enclosure Status 125
- Viewing Component Properties 126
- Components 127
- Behavior 130
- SEP MASTER 132
- Sending a Test Message 134
- Modifying Email Settings 135
- Disabling Email Notifications 135
- Sending a Test Trap 137
- Disabling SNMP Traps 137
- The server is offline 138
- 4 Click OK 144
- Updating and Customizing 145
- Adaptec Storage Manager 145
- Viewing Display Group Status 148
- Modifying Display Groups 148
- Solving Problems 149
- Silencing an Alarm 154
- Hot Swapping Disk Drives 156
- Rebuilding Pools 158
- Disk Manager 166
- IP Address 167
- Configuring iSCSI Initiators 169
- Configuration Notes 171
- (Target Portal) 172
- Automatically restore 173
- Microsoft Windows 178
- Requirements 178
- 3 Click OK to save changes 183
- Using the CLI 185
- Access Levels and Passwords 186
- About Parameters 189
- About Manage Commands 189
- Command Abbreviation 189
- Command Completion 190
- Command Line Editing 191
- Viewing Long Reports 192
- Getting Help 193
- Your Snap Server 700i Series 195
- Product Descriptions 196
- Where to Buy tab 197
- Component Description 198
- Optional Expansion Arrays 199
- Componen 202
- Specifications 204
- SANbloc S50 Specifications 205
- Safety Precautions 206
- RAID Quick Reference 207
- Expanding Pool Capacity 208
- Completing a Silent Windows 209
- Installation 209
- Property Values 210
- MGMTPASS=pass” 213
- OS Support Quick Reference 215
- Supported iSCSI Initiators 216
- Windows OSs 216
- Windows Support Components 217
- OS with Latest Service 217
- Windows Server 2003: 217
- Glossary 219
- Term Definition 220
Relacionado con productos y manuales para Servidores Adaptec Snap Server 700i Series
Servidores Adaptec ASR-6805 Guía de usuario
(8 paginas)
(8 paginas)
Servidores Adaptec ARO-1130SA Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales