Adaptec ASA-7211C/F Guía de instalación

ASA-7211C/F iSCSI ADAPTERFOR INITIATOR APPLICATIONSINSTALLATION GUIDEASA-7211 IG.book Page 1 Monday, February 2, 2004 10:33 AM

1-4ASA-7211C/F Installation GuideInstallation OverviewThe following steps provide an overview of the process of installing and configuring the ASA-721

1-5IntroductionSystem RequirementsThe following system requirements are discussed: Hardware requirements Supported iSCSI targets Operating system r

1-6ASA-7211C/F Installation GuideLinuxThe following Linux versions are supported: Red Hat Version 9.0 Red Hat Advanced Server 2.1 SuSE Version 8.2

1-7Introductioninstallation CD to the hard drive. See Installing and Running the iConfig Utility on page 5-5.About the DocumentationThe Adaptec iSCSI

2-12Installing the Adaptec iSCSI AdapterTo install the adapter in a PCI slot in a computer:1 Before handling the board or any computer components, dis

2-2ASA-7211C/F Installation Guide5 Insert the adapter in the PCI expansion slot. Press the board firmly into the slot until it clicks into place. Note

3-13Installing the Driver in Existing SystemsIn this Chapter...Now that you have installed the adapter in the computer and connected the Ethernet cabl

3-2ASA-7211C/F Installation GuideInstalling the Windows DriverThis section contains the following procedures: Installing the Driver in Windows Server

3-3Installing the Driver in Existing Systems11 Select Search for the best driver in these locations and select Include this location in the search. De

3-4ASA-7211C/F Installation GuideInstalling the Driver in Windows 2000To install the driver:1 Install the Adaptec iSCSI adapter according to the instr

iiCopyright©2002 – 2004 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted

3-5Installing the Driver in Existing SystemsThe driver has been installed. The system does not require rebooting. To verify the driver installation, o

3-6ASA-7211C/F Installation GuideInstalling the Driver in Windows NT 4.0To install the driver:1 Install the Adaptec iSCSI adapter according to the ins

3-7Installing the Driver in Existing SystemsInstalling the Linux ModuleThis section contains the following procedures: Installing the Module Using th

3-8ASA-7211C/F Installation Guide7 Run the configure script:./configureIf the kernel source is not in /usr/src/linux-2.4, run the configure script usi

3-9Installing the Driver in Existing SystemsInstalling to the Module Using the .tar.gz PackageTo install the module:1 Mount the Adaptec installation C

3-10ASA-7211C/F Installation Guide9 Run the configure script:./configureIf the kernel source is not in /usr/src/linux-2.4, run the configure script us

4-14Creating an iSCSI-Bootable SystemIn this Chapter...Now that you have installed the adapter in the computer and connected the Ethernet cables, you

4-2ASA-7211C/F Installation GuideConfiguring the iSCSI Adapter BIOSOverviewConfiguring the BIOS involves the following tasks:1 Optional—Configure the

4-3Creating an iSCSI-Bootable System6To create a single boot target entry, select Target Configuration > Add Targets and press Enter. a For the tar

4-4ASA-7211C/F Installation GuideInstalling the Driver with WindowsTo install the driver during a fresh install of the operating system, you need to p

iiiRegulatory Compliance StatementsFederal Communications Commission Radio Frequency Interference StatementWARNING: Changes or modifications to this u

4-5Creating an iSCSI-Bootable System5 Proceed with the Windows installation, responding to prompts and instructions as needed.Installing the Module wi

4-6ASA-7211C/F Installation GuideInstalling the OS and Module1 Restart the computer and boot from the Linux installation CD.2 For Red Hat—Insert the d

5-15Configuring the iSCSI SystemIn this ChapterNow that you have installed the Adaptec iSCSI adapter, Ethernet cables, and driver, you need to run the

5-2ASA-7211C/F Installation GuideUsing the Express Setup WizardThis section describes the Express Setup wizard, which starts automatically when you st

5-3Configuring the iSCSI System2 Choose an initiator iSCSI name. Adaptec recommends that you apply the default name. However, you can assign your own

5-4ASA-7211C/F Installation Guide5 Select the method for target discovery, then click Next. 6 If you are satisfied with your configuration settings, c

5-5Configuring the iSCSI SystemUsing the iConfig Utility – Linux onlyiConfig has an easy-to-use Express Setup that prompts you for the information the

5-6ASA-7211C/F Installation GuideUsing Express Setup to Configure the iSCSI AdapterNow that you have started iConfig, you are ready to run iConfig Exp

5-7Configuring the iSCSI SystemChanging the iConfig PasswordThe default user ID is admin. The default password is adaptec. To change the default passw

A-1AUpdating the DriverIn this Chapter...This Appendix describes how to update the driver if you already have an iSCSI adapter installed in the comput

ivCanadian Compliance StatementThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Cet ap

A-2ASA-7211C/F Installation GuideUpdating the Driver in Windows Server 2003Note: If you update the operating system to Windows Server 2003, you need t

A-3Updating the DriverUpdating the Driver in Windows 2000To update the driver:1 Insert the disk containing the new driver.2 Open the Windows Device Ma

A-4ASA-7211C/F Installation GuideUpdating the Driver in Windows NT 4.0This section describes the following procedures: Removing the Old Driver Addin

A-5Updating the DriverUpdating the Linux ModuleIn order to update the Linux asa72xx module, you need to first remove the old module prior to installin

B-1BLEDsYou can use the adapter LEDs to diagnose problems during system startup and as speed indicators during normal system operation. The following

RAdaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035 USA©2002 – 2004 Adaptec, Inc.All rights reserved. Adaptec and the Adaptec logo are tradem

vContents1 Introduction Kit Contents 1-2Adaptec iSCSI Adapter Features 1-2Adapter Illustrations 1-3Installation Overview 1-4System Requirements 1-5Har

viASA-7211C/F Installation Guide4 Creating an iSCSI-Bootable System Configuring the iSCSI Adapter BIOS 4-2Overview 4-2Using the iSCSISelect Utility 4-

1-11IntroductionIn this Chapter...The Adaptec® Storage Accelerator (ASA) 7211 iSCSI storage adapter is a PCI Host Bus Adapter (HBA) that enables serve

1-2ASA-7211C/F Installation GuideKit ContentsThe Adaptec iSCSI kit includes: ASA-7211 adapter card, shown on page 1-3. Adaptec iSCSI installation CD

1-3IntroductionAdapter IllustrationsThe Adaptec iSCSI adapters are illustrated below. Note the difference in external connectors. One adapter has a co