Adaptec ASC39320A-ROHS-KIT Guía de usuario Pagina 44
- Pagina / 206
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-3
Configuring the Adaptec SCSI Card with SCSISelect
Starting SCSISelect
To start SCSISelect:
1 Turn on or restart your computer.
During the startup process, pay careful attention to the
messages that appear on your screen.
2 When the following message appears on your screen, press the
Ctrl-A keys simultaneously (this message appears for only a
few seconds):
Press <Ctrl><A> for SCSISelect (TM) Utility!
3 Select SCSI Channel A or B.
4 From the menu that appears, use the arrow keys to move the
cursor to the option you want to select, then press Enter.
Display <Ctrl> <A> Messages during
BIOS Initialization
[Auto-sync]
Enabled, Disabled Enabled
Extended INT 13 Translation for
DOS Drives > 1 GB
Enabled, Disabled Enabled
Post Display Mode [Auto-sync] Verbose, Silent,
Diagnostic
Ver bo se
SCSI Controller INT 13 Support Enabled
Disabled: Scan
Bus
Disabled: Not Scan
Enabled
Domain Validation Enabled, Disabled Enabled
Support Removable Disks Under
INT 13 as Fixed Disks
2
Disabled,
Boot Only,
All Disks
Disabled
BIOS Support for Bootable CD-ROM
2
Enabled, Disabled Enabled
HostRAID Options:
HostRAID Enabled, Disabled Disabled
1
Setting is valid only if Multiple LUN Support is enabled.
2
Settings are valid only if host adapter BIOS is enabled.
SCSISelect Options Available Settings Default Setting
U320 UG.book Page 3 Tuesday, September 23, 2003 1:47 PM
- USER’S GUIDE 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Adaptec Customer Support 3
- SCSISelect 10
- 2003, and XP 11
- OpenServer, and Open Unix 13
- Browser Edition 14
- A Troubleshooting in Windows 14
- Contents 15
- Glossary 16
- Introduction 17
- ■ Adaptec SCSI Card 39320A 18
- Device Drivers 19
- HostRAID Features 20
- Storage Management Software 21
- Operating Systems 22
- System Requirements 23
- Understanding SCSI 24
- SCSI IDs 24
- Terminating the SCSI Bus 25
- Defining RAID 26
- Supported RAID Levels 27
- Using the Adaptec SCSI 28
- Card and SCSI Devices 28
- Using SCSI Devices 29
- Connecting the LED Connector 34
- Adaptec SCSI Card 39320A 35
- Adaptec SCSI Card 29320A 35
- Connecting SCSI Devices 36
- Adaptec SCSI Card 29320ALP 39
- Built-in Terminator on Cable 40
- Terminated Device 40
- Maximum Cable Lengths 41
- SCSI Card with SCSISelect 42
- Configuring the Adaptec 42
- Starting SCSISelect 44
- Using SCSISelect Settings 45
- Options – BBS Systems Only 46
- HostRAID Options 52
- ■ Boot Device Configuration 54
- ■ SCSI Device Configuration 54
- Using SCSI Disk Utilities 57
- Using the SCSISelect Utility 61
- =default) 63
- 39320A at slot 6, 00:0E:00 63
- Creating Arrays 65
- ■ RAID-0 66
- ■ RAID-1 66
- ■ RAID-10 66
- Creating RAID 0 Arrays 67
- Creating RAID 1 Arrays 68
- Creating RAID 10 Arrays 69
- Create Array? 70
- Are you sure? 70
- Deleting Arrays 71
- Adding a Spare Drive 71
- Rebuilding Arrays 72
- Verifying Data Integrity 73
- Bootable Array 75
- Check Point 75
- Installing the HostRAID 76
- Driver for Windows 2000 76
- 2003 is Already Installed 78
- Configuration Notes 80
- Driver for Windows NT 4.0 81
- If Windows NT 4.0 Setup Hangs 84
- Driver for Linux 86
- Installing Red Hat Linux 87
- Installing SuSE Linux 88
- For Windows 2000/2003 90
- Windows NT 100
- Already Installed 102
- Hot-Plug PCI Support 103
- Removing a Host Adapter 104
- Swapping a Host Adapter 105
- Troubleshooting 107
- Error Messages 109
- Installing the SCSI Driver 110
- NetWare 5.1 and 6.x 111
- Installed 112
- Sample Load Commands 115
- Using Removable Media 115
- Using the NetWare Tape Backup 117
- Using a CD with NetWare 118
- Optimizing Performance 118
- Open Unix 123
- Back Up the Kernel 126
- Load the Package 126
- Modify the New System File 127
- Boot the New Kernel 128
- OpenServer 129
- Using Tunable Parameters 130
- Removing the Driver 131
- /reconfigure file by typing: 140
- Command Line Options 141
- Additional Notes 142
- Installing Adaptec Storage 145
- Manager–Browser Edition 145
- Supported Browsers 146
- Autorun 147
- Logging On 152
- Troubleshooting in 154
- Troubleshooting Checklist 155
- General Troubleshooting 156
- Common Error Messages 159
- Windows Error Messages 160
- Driver Error Messages 161
- Using Windows Advanced 164
- Configuration Parameters 164
- Using Windows SCSI Parameters 165
- Creating Driver Floppy 169
- Installation Options 170
- Running Windows 171
- Running OpenServer 172
- Running Linux 173
- Running DOS/NetWare 173
- Migrating From Adaptec 175
- Ultra320 SCSI to HostRAID 175
- Migrating With Windows 2000 176
- Enabling HostRAID Support 177
- Migrating With Windows XP 179
- Migrating With Windows NT 4.0 181
- Migrating from HostRAID 184
- Disabling HostRAID Support 186
- Glossary-2 195
- Glossary-3 196
- Glossary-4 197
- Glossary-5 198
- Glossary-6 199
- Glossary-7 200
- Adaptec, Inc 206
- 691 South Milpitas Boulevard 206
- Milpitas, CA 95035 USA 206
Relacionado con productos y manuales para Tarjetas de interfaz / adaptadores Adaptec ASC39320A-ROHS-KIT
(14 paginas)
(30 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales