Adaptec ICP9085LI Guía de usuario Pagina 52
- Pagina / 113
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 8: Installing the Driver on an Existing Operating System ● 52
Before You Begin
Before you begin, install and connect your ICP RAID controller and internal disk drives (see
page 33).
You must also create a driver disk (see page 46) before you begin installing the controller driver.
Creating a Driver Disk
Note: You will need a floppy disk to complete this task.
To create a driver disk:
1 Set your system BIOS so that your computer boots from the CD drive. (For instructions,
refer to your computer’s documentation.)
2 Turn on your computer, then insert the RAID Installation CD included in your RAID
controller kit.
3 Follow the on-screen instructions to get to the ICP Start Menu.
4 Click Create Driver Disk(s) for Installing/Updating your OS, then select your operating
system.
● Windows
● Linux
● NetWare
● UnixWare
● Solaris
● FreeBSD
Note:
Linux only—If prompted, select your operating system and then the version.
5
When prompted, insert a floppy disk, then click OK.
The system creates the driver disk.
6 Remove and label the driver disk.
7 Continue with the instructions for your operating system:
● For Windows, see page 53.
● For Red Hat or SUSE Linux, see page 53.
● For NetWare, see page 53.
● For OpenServer, see page 54.
● For UnixWare, see page 54.
● For Solaris, see page 55
● For FreeBSD, see page 55.
- SAS, SATA, and SCSI 1
- RAID Controllers 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- ICP vortex Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Using the ICP Flash Utility 10
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- System Requirements 14
- CD drive 15
- About Your RAID Controller 16
- Array-level Features 17
- RAID Controller Battery Model 18
- About the ICP5445AU 19
- About the ICP5085AU 20
- About the ICP9085LI 21
- About the ICP5085BR 22
- About the ICP9047MA 23
- About the ICP9087MA 24
- About the ICP9014RO 25
- About the ICP9024RO 26
- Getting Started 27
- Choosing a RAID Level 28
- Selecting Disk Drives 29
- Selecting Cables 30
- SATA Cables 31
- SCSI Cables 31
- Installation Options 32
- Basic Installation Steps 32
- In this chapter 33
- Before You Begin 34
- Installing the Controller 34
- Devices on page 38 36
- Disk drives on 37
- Controller connected to 37
- Connecting External Devices 38
- Failed Device is faulty On 39
- Other No error Off 39
- Creating a Bootable Array 40
- Setting the Boot Controller 41
- Creating an Array 41
- Making Your Array Bootable 44
- Installing the Driver and an 45
- Operating System 45
- Creating a Driver Disk 46
- Installing with Windows 47
- Installing with Red Hat Linux 47
- Installing with SUSE Linux 48
- Installing with NetWare 48
- Installing with OpenServer 49
- Installing with UnixWare 49
- Installing with FreeBSD 50
- Installing on Windows 53
- Installing on NetWare 53
- Installing on OpenServer 54
- Installing on UnixWare 54
- Installing on Solaris 55
- Installing on FreeBSD 55
- Managing Your Storage Space 56
- About ICP Storage Manager 57
- About the ICP Flash Utility 58
- Which Utility Should I Use? 58
- Solving Problems 59
- Troubleshooting Checklist 60
- Silencing the Alarm 60
- Resetting the Controller 62
- In this appendix 63
- ) Web site at www.scsita.org 63
- What is SAS? 64
- What’s a Phy? 65
- What’s a SAS Port? 66
- What’s a SAS Address? 66
- What’s a SAS Connector? 66
- What do SAS Cables Look Like? 66
- Direct-attach Connections 67
- Backplane Connections 67
- SAS Expander Connections 68
- Understanding RAID 70
- Understanding Drive Segments 71
- Nonredundant Arrays (RAID 0) 71
- RAID 1 Arrays 72
- RAID 1 Enhanced Arrays 72
- RAID 10 Arrays 73
- RAID 5 Arrays 74
- RAID 5EE Arrays 75
- RAID 50 Arrays 76
- RAID 6 Arrays 77
- RAID 60 Arrays 77
- Selecting the Best RAID Level 78
- Creating a New Array 80
- Managing Existing Arrays 81
- Initializing Disk Drives 81
- Rescanning Disk Drives 81
- Secure Erasing Disk Drives 82
- Opening a -Select Utility 82
- Applying Changes and Exiting 82
- General Controller Settings 83
- Option Description 84
- Viewing the Event Log 86
- Running the ACU Using Scripts 89
- About Record Mode 90
- Required 91
- ? Description 91
- HotspareDrives=0:0:0,0:1:0 92
- Type=Volume 92
- Type=RAID1 92
- ACU exits with an error 93
- Keyword Description 94
- ACU Error Codes 95
- Sample Scripts 96
- Running the Menu-based IFU 100
- Running the 101
- Current Requirements 107
- Environmental Specifications 107
- DC Power Requirements 107
- Index ● 109 109
- Index ● 110 110
- Index ● 111 111
- Index ● 112 112
- Konrad-Zuse-Str.9 113
- 74172 Neckarsulm 113
Relacionado con productos y manuales para Controladores De Periféricos Adaptec ICP9085LI
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales