Adaptec ICP5045BL Guía de usuario Pagina 48
- Pagina / 135
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 7: Installing the Driver and an Operating System ● 48
Before You Begin
● Install and connect your ICP RAID controller and internal disk drives (see page 36).
● Create a bootable array (see page 42).
● Create a driver disk (see the following section).
Note:
For up-to-date operating system version support, visit the ICP Web Site at www.icp-
vortex.com. From the main menu select Download>firmware, drivers, tools. Select your
controller type and version to generate a list of supported operating systems.
Creating a Driver Disk
Note: You will need a floppy disk to complete this task.
To create a driver disk:
1 Set your system BIOS so that your computer boots from the CD drive. (For instructions,
refer to your computer documentation.)
2 Turn on your computer, then insert the RAID Installation CD included in your RAID
controller kit.
3 Follow the on-screen instructions to get to the ICP Start Menu.
4 Click Create Driver Disk(s) for Installing/Updating your OS, then select your operating
system.
● Windows
● Linux
● NetWare
● OpenServer
● Solaris
● UnixWare
Note:
Linux only—If prompted, select your operating system and then the version.
5
When prompted, insert a floppy disk, then click OK.
The system creates the driver disk.
6 Remove and label the driver disk.
7 Continue with the instructions for your operating system:
● For Windows, see page 49.
● For Red Hat Linux, see page 49.
● For SUSE Linux, see page 50.
● For NetWare, see page 50.
● For OpenServer, see page 51.
● For Solaris, see page 51
● For UnixWare, see page 52.
- SAS, SATA, and SCSI 1
- RAID Controllers 1
- Installation and 1
- User’s Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- ICP vortex Customer Support 3
- Canadian Compliance Statement 5
- Contents 6
- Using the ICP Flash Utility 10
- Safety Information 10
- Technical Specifications 10
- About This Guide 11
- How to Find More Information 12
- Kit Contents and System 13
- Requirements 13
- Kit Contents 14
- About Your RAID Controller 15
- Array-level Features 16
- RAID Controller Battery Model 17
- About the ICP5805BL 18
- About the ICP5045BL 19
- About the ICP5085BL 20
- About the ICP5125BR 21
- About the ICP5165BR 22
- About the ICP9085LI 23
- About the ICP5085BR 24
- About the ICP9047MA 25
- About the ICP9087MA 26
- About the ICP9014RO 27
- About the ICP9024RO 28
- Getting Started 29
- Choosing a RAID Level 30
- Selecting Disk Drives 31
- Selecting Cables 32
- SATA Cables 33
- Installation Options 34
- Basic Installation Steps 34
- In this chapter 36
- Installing the Controller 37
- Connecting External Devices 41
- Creating a Bootable Array 42
- Setting the Boot Controller 43
- Creating an Array 43
- Making Your Array Bootable 46
- Installing the Driver and an 47
- Operating System 47
- Creating a Driver Disk 48
- Installing with Windows 49
- Installing with Red Hat Linux 49
- Installing with SUSE Linux 50
- Installing with NetWare 50
- Installing with OpenServer 51
- Installing with Solaris 51
- Installing with UnixWare 52
- Installing with VMware 52
- Installing with FreeBSD 53
- Installing on Windows 56
- Installing on NetWare 56
- Installing on OpenServer 57
- Installing on Solaris 57
- Installing on UnixWare 58
- Installing on VMware 58
- Installing on FreeBSD 59
- Managing Your Storage Space 60
- About ICP Storage Manager 61
- About the ICP Flash Utility 62
- Which Utility Should I Use? 62
- Solving Problems 63
- Troubleshooting Checklist 64
- Silencing the Alarm 64
- Resetting the Controller 66
- In this appendix 67
- ) Web site at www.scsita.org 67
- What is SAS? 68
- What’s a Phy? 69
- What’s a SAS Port? 70
- What’s a SAS Address? 70
- What’s a SAS Connector? 70
- What do SAS Cables Look Like? 70
- Direct-attach Connections 71
- Backplane Connections 71
- SAS Expander Connections 72
- Understanding RAID 74
- Understanding Drive Segments 75
- Non-redundant Arrays (RAID 0) 75
- RAID 1 Arrays 76
- RAID 1 Enhanced Arrays 76
- RAID 10 Arrays 77
- RAID 5 Arrays 78
- RAID 5EE Arrays 79
- RAID 50 Arrays 80
- RAID 6 Arrays 81
- RAID 60 Arrays 81
- Selecting the Best RAID Level 82
- Creating a New Array 84
- Managing Existing Arrays 85
- Initializing Disk Drives 85
- Rescanning Disk Drives 85
- Secure Erasing Disk Drives 86
- Opening a -Select Utility 86
- Applying Changes and Exiting 86
- General Controller Settings 87
- Option Description 88
- Locating Disk Drives 90
- Identifying Disk Drives 90
- Viewing the Event Log 91
- Running the ACU Using Scripts 94
- About Record Mode 95
- Required 96
- ? Description 96
- HotspareDrives=0:0:0,0:1:0 97
- InitializeAll=Yes 97
- ACU exits with an error 98
- Keyword Description 99
- ACU Error Codes 100
- Sample Scripts 101
- System Requirements 104
- Before You Begin 104
- Running the Menu-based IFU 105
- Running the 106
- Connector Reference 110
- Pin Number Signal Description 111
- 22-55-2161 113
- Pin Number 113
- SFF-8087 Connector J5: 120
- SFF-8087 Connector J18: 120
- SFF-8087 Connector J14: 124
- 22-552101 125
- Environmental Specifications 129
- DC Power Requirements 129
- Current Requirements 129
- Index ● 131 131
- Index ● 132 132
- Index ● 133 133
- Index ● 134 134
- Konrad-Zuse-Str.9 135
- 74172 Neckarsulm 135
Relacionado con productos y manuales para Controladores De Periféricos Adaptec ICP5045BL
(148 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales